THERMAL CONDUCTIVITY OF MERTAL ROD, LIQUID, POWDER

Features:

• M. S. powder coated Storage tank with flow
• Measuring Flask , Dye bottle tank
• Transparent tube 1 meter long wit 25 mm ID.
• Stand to mount glass tube, Potassium Paramagnet provided as dye.
• M. S. powder Sump Tank

Features:

• MS powder coated Tanks : 2 numbers of suitable size mounted on stand.
• Flow channel of 750 mm length made out of perspex sheets.
• Piezometer tubes equally spaced at 5 cm
• MS powder coated Measuring tank.
• Stop clock. Sump tank

Features:

• M. S. powder coated tank with drain plug.
• A hollow ship model with balancing weight.
• Circular weight 4 in numbers.
• A graduated arc for measuring tilt angle.
• M. S. powder coated Ship size.

Features:

• Size approx. 220 mm x 360 mm height.
• Transparent Heleshaw Apparatus.
• Suitable stand.
• Two dimensional models of cylinder, aerofoil,Square & triangular.
• Measuring cylinder

Features:

• M. S. powder coated S. storage tank provided with four sets of baffles and sieves for steadying water supply, fixing arrangement for interchangeable notches.
• M. S. powder coated Measuring tank with drain valve & gauge glass.
• M. S. powder coated Sump Tank.
• Set of 2 brass Notches:Rectangular Notch,'V’ Notch 60°C

Features:

• Three pipes nominal diameters approximately connected in a common manifold.
• Pressure tapping at 1 m distance.
• Supporting stand structure for the equipment.
• MS powder coated Measuring tank with drain valve & gauge glass.
• Differential manometer of 300 mm length with mercury

Features:

• Transparent cylinder mounted on a stand.
• Differential lever mechanism with adjustable load screw mechanism & dead weight to measure the force.
• Sump Tank MS powder coated
• Measuring tank MS powder coated with drain
• Two nozzles with inside section Straight taper ,Curved taper
• Semicircular vane with angle of deflection 180°
• Curved vane with angle of deflection 135°
• Horizontal flat vane angle of deflection 90°
• 60° inclined flat vane
• 30° inclined flat vane.

Features:

• Storage Tank MS powder coated.
• Collecting Tank MS powder coated Capacity approx. 60 liters, fitted with drain valve “1” size. Manometer tube with calibrated marking scale.
• Monoblock Pump : Monoblock, 1ph, ½ HP pump shall be provided with the set-up which shall be mounted on the base plate. Necessary piping with by-pass valve and suction piping are provided. The connection for the test equipment is made by flexible House pipe.
• Differential manometer of 300mm length with mercury.

Features:

• MS powder coated Sump tank with flow.
• MS powder coated Measuring tank.
• Mercury Manometers(Differential).
• Each line provided with flow control value for setting of different flow rates.
• Pressure tubes of different pipe lines are connected to common manometer through cocks.
• Easy to operate and replacement of Venturimeter & Orifice meter.
• Flow control value at the end of each line assures full running of pipe.
• Differential manometer of 300 mm length with mercury

Features:

• 0.5 HP Mono block cylinder.
• Universal Motor Free Vortex Flow
• Acrylic Vessel Ø 200 x 300mm
• MS powder coated Sump tank.
• MS powder coated Measuring Tank.

Features:

• 300mm height Differential Manometer
• Measuring Tank MS powder coated.
• Supply Tank MS powder coated.

Features:

• 0.5 H.P. pump to circulate water system through the piping.
• Sump tank : 1000 x 300 x 400 mm
• Measuring tank : 300 x 300 x500mm
• Rotameter of range 250 to 2500 LPH

Features:

• Storage Tank MS powder coated.
• Measuring Tank MS powder coated.
• Collecting Tank MS powder coated: Size of the collecting Tank is fitted with drain valve 1” size Mano meter Tube. With marking scale.
• Monoblock Pump 1ph, ½ HP pump.
• The equipment is a set-up used to study the performance of Orifice meter & Mouth Piece

Features:

• Centrifugal Pump 1HP/2HP, with DC motor variable speed type 4 Amp OR With AC motor & Pulley Type
• Sump tank - 1000 x 700 x 300m height
• Measuring tank - 600 x 400 x 250mm height
• Energy meter, Vacuum Gauge, Pressure Gauge, On / Off Switch

Features:

• Centrifugal pump Mono block 2 stage pump with 1HP single phase induction motor
• Sump tank - 1000 mm x 300 mm x 400 mm height
• Measuring tank OR Venturi Meter & Pressure Gauge.
• Energy meter for motor input measurement.
• Pressure gauge at 1st and 2nd stage delivery & vacuum gauge at suction for measurement of head.
• Stop watch, assembly of pump & control are mounted on the sump tank.

Features:

• Speeds size 1/2 " X ¾ " to discharge 220 GPH at 40m. head, (approx.) electric motor of capacity 1 HP A.C. OR D.C. motor single phase drive from the motor to pump is given by a variable reduction pulley belt drive OR Dimmer Stat
• Variable speed arrangement by reduction Pulley.
• Pressure gauge, Vacuum gauge, foot valve,
• Energy meter. Switch, starter, and stop clock.
• MS. Powder coated Measuring tank with scale Fitting and I “drain valve
• MS. Powder coated Sump Tank.

Features:

• MS powder coated Sump Tank
• Specific Speed Approx. 19 RPM, Net Head 45m Approx.
• Discharge Approx. 820 LPH approx, Normal Speed 750 RPM.
• Power 1kw ( 5HP motor), Runner Diameter 250 mm, Number Of Buckets 16
• Brake Drum Diameter 200 mm.
• Centrifugal Pump set suitable for supply of water of size coupled to 5 HP induction motor 3 phase 400 V. A. C. supply.
• Starter switch, piping, foot valve, gate valve.

Features:

• A Pressure gauge and Vacuum Gauge for head measurement.
• Rope brake arrangement by two circular balance methods.
• 300mm dia. cast iron water-cooled brake drum mounted on the main shall with bearings for load test. The head of the turbine is 5 to 8 meters and discharge about 1500 LPM.
• 1HP/5 HP pump set suitable for supplying water to the above turbine and for operation on 400 Volts 3 phase 50 cycles AC mains.
• TPIC Switch and DOL, starter for the Pump set.
• Flow measuring unit, consisting of 150mm Orifice meter and pressure gauge.
• Piping system consisting of pipes, valves, and fittings complete set suitable for the test rig.
• Fiber glass lined MS. Powder coated Sump tank to store sufficient water for independent circulation through the unit for experimentation and arranged within the floor space of the main unit.
• M. S. powder coated framework compactly lilted with all the above items as a self-sufficient package unit suitable for operation without any foundation.

Features:

• Francis Turbine Horizontal type of size 75 mm, develop about 1kW output, made of cast iron spiral casing, bearing housing and Airfoil shaped gun metal guide vane and gun metal runner Transparent outlet pedestal with stainless steel draft tube.
• The cast iron external bearing pedestal for longer bearing life. A Cast iron base plate and slotted dead weights for conducting experiments in metric units. Pressure gauge and a vacuum gauge for head measurement in meters. 300mm dia. cast iron water-cooled brake drum mounted on the main shaft with bearings for load test. The head of the turbine is 10 meters and discharge at about 1000 LPM.
• 1HP/5 HP supply pump set 75mm size, 1000 LPM at 14 meters head suitable for supplying water to the above turbine and for operation on 400 Volts 3 phase 50 cycles AC mains.
• Switch and DOL Starter suitable for the above Mono block pump set, mounted on a panel board.
• Flow measuring unit, consisting of a suitable orifice meter, pressure gauges.
• Piping system consisting of nines, valves, fittings complete with suitable for the test rig.
• Fiber glass lined M. S. Sump to store sufficient water for independent circulation through the unit for experimentation and arranged within the floor space of the main unit.
• M. S. powder coated framework compactly lilted with all the above items as a self-sufficient package unit, suitable for operation without any foundation.

Features:

• Over Head tank-100 lit capacity.
• Head over Ram - 2m
• Diameter of Supply pipe 50mm.
• Diameter of delivery - 15mm.
• Valve chamber comprising of waste valve and a delivery valve.
• A non return valve fitted in delivery pipe.

Features:

• ½ H.P. pump to circulate water through the piping.
• MS powder coated Sump tank of 1000 mm x 300 mm x 400 mm capacity.
• MS powder coated Measuring tank of 300 mm x 300 mm x 500 mm height.
• Pressure gauge, Vacuum gauge, U-tube manometer 300 mm height.
• Differential manometer 300 mm, 45°C, Single tube manometer

Features:

• Pumps : 1 HP, 40 to 50 LPM discharge at 20m. Head, 2 nos.
• Motor : 2880 rpm of suitable capacity with variable speed drive. 2 nos.
• Measurement Tank OR Rotameter:To measure discharge.
• Energy meter To measure electrical input.
• Pressure and vacuum gauges one each for each pump

Features:

• Vane compressor - Rotary compressor, driven by 0.5HP single phase motor.
• Calibrated orifice meter with water manometer 300 mm height to measure air intake.
• Energy enter to measure input of the meter.
• Pressure gauge to measure discharge pressure.
• Control valve at delivery side, Stop clock.
• Temperature Indicator 0 to 200 °C.
• Storage tank suitable.

Features:

• Size: Size - 0.25 m width. 0.30 m depth & 2.5 m test section length.
• A point gauge mounted on a trolley.
• Inlet pipe piece containing an orifice in it.
• Differential manometer (without mercury)
• Screw jack for adjusting slope.