Sensor Controls System Trainer

Features:

• Simulated blocks like dead time (transportation lag), integrator, time constant, error detector and gain.
• PID Controller Prop: Band 5% to 50% (Gain 2-20), Integral time: 10msec-100msec, Derivative time : 2-200msec
• Built-in signal sources Value of -1V to +1V, Square wave & Triangular of 1V p-p (min) at 40Hz, Built-in 3 ½ digit DVM for DC measurements

Features:

• Simulated first, second and third order system of type-0 and type-1
• Calibrated variable gain amplifier (Resolution 1:1000)
• Built-in signal sources of Square wave and Triangular Frequency of 45-90Hz With Amplitude 0-2.5V.
• Uncommitted amplifier for phase adjustment, Provision for disturbance inputs.

Features:

• High quality servo-potentiometers of 360 degree shaft rotation.
• Built-in signal and power sources.
• 3½ digits DVM for measurements.

Features:

• Synchro transmitter-receiver pair with calibrated dials enclosed In see through metal cabinet
• Locking system for receiver rotor, Receiver use as control transformer
• Built-in balanced demodulator circuit, Panel meter for ac/dc voltages

Features:

• Temperature controller with facilities for P. I, D and relay control blocks.
• Operating temperature: Ambient to 900C.
• Separate controls for P, I, D channel gains, Two settings for relay hysteresis.
• Fast 25W oven fitted with IC temperature sensor.
• Digital display of set and measured temperature on 3 ½ digit built-in DVM.

Features:

• Study of 4 different temperature transducers - NTC thermistors, RTD Platinum, K(Cr-Al) thermocouples, IC temperature sensors.
• Study & comparison of Temperature transducer controlled alarm system
• PID control: P, P+I, P+D & P+I+D control action
• Instrumentation amplifier, adder amplifier : X1, X100, X235, P controller, I controller, D controller Comparator, Electronic switch, Signal conditioning, Rotary /Slide pots, Heater, Relay, Buzzer, LED
• Digital meter: Actual/Set temp/mV.

Features:

• Simulated electronic relay using high speed IC’s.
• Simulated 2nd order linear plant. Facility for displaying x and x’ signaling.
• Dead zone variable from 0-600mV, Hysteresis variable from 0-500m
• Built-in Signal source- Sine and Square Amplitude: 0-1V (min) with Variable Frequency: 10 to 1000Hz.

Features:

• Speed control of a 12V, 4W permanent magnet d.c. motor enclosed In see through Metal cabinet
• Speed range: 0 to 3000 rpm (typical), Opto-interrupter based speed sensing.
• 4-digit speed display in rpm, Electronic tachogenerator for feedback.
• Separate unit for motor in a see-through cabinet, Smooth, non-contact eddy current brake for loading.
• Built-in 3 ½ digit DVM for signal measurements.

Features:

• Simulated ‘uncompensated’ system having adjustable damping. Peck percent overshoot Mp, variable from 20% to 50%, and steady state error variable from 50% to 0.5%
• Compensation network implementation through built-in variable gain amplifier. Gain is adjustable from 1 to 11.
• Built-in square and sine wave generators for transient and frequency response studies. Frequency adjustable from 25Hz – 800Hz (approx).

Features:

• Single stepping and free running modes of operating with speed variation and direction reversal – internal TTL circuit.
• 360O motion Servo-Potentiometer position-pickup for motor dynamics.
• Operation through microprocessor kit-sample control programs provided.
• Stepper motor enclosed in see through metal cabinet, Torque 3 Kg-cm, Step angle 1.8 O, Power 12V, 1A/ phase.

Features:

• Second order simulated process (analog process)
• Built-in D/A and A/D circuit (8-bit)
• 8085 based µP-kit as digital controller with user software in 8K EPROM.
• 16-bit arithmetic for algorithm calculations.
• Square wave test input (internal).
• 16 built-in levels of p. I and D gain each.

Features:

• 2-phase a.c. servomotor – 12V/50Hz per phase enclosed in see through metal cabinet.
• Small generator for loading.
• 4-digit speed display, 3-digit time constant display.
• 3 ½ digit r.m.s. voltmeter, 3 ½ digit d.c. panel meter.

Features:

• Position control of a 12V, 1A d.c. gear motor (50rpm) with calibrated dials coupled with tacho-generator enclosed in see through metal cabinet
• Provision for positive and negative tachogenerator feedback.
• Tacho constant: 2V/ 1000 rpm approximately.
• Calibrated dials for reference and output position: resolution 1 degree
• µP based waveform capture card.
• Built-in 3 ½ digit DVM for signal measurements.
• Built-in step signal and IC regulated power supplies for electronic circuit.
• Servo-potentiometer with full 360 degree rotation.
• Separate unit for motor in a see-through cabinet.

Features:

• 2-phase servomotor 12V/ phase, 50Hz, 10W with calibrated dials coupled with Potentiometer enclosed in see through metal cabinet.
• Power amplifier.
• Servo potentiometer type error detector.
• In-built 10.00V (rms) panel meter.
• µP based waveform capture card.

Features:

• Light Sensor like Photoconductive Cell, Photovoltaic Cell, Phototransistor, PIN Photodiode
• On board Filament Lamp Light Source
• Signal Conditioning Circuitry : Power Amplifier, Current Amplifier, DC Amplifier, Comparator, Electronic Switch, Buffer
• On board Rotary, Slide Potentiometers, Relay & LED circuits provided.

Features:

• Speed control of a 30V/2A, permanent magnet d.c. motor coupled
• With tachogenerator enclosed in see through metal cabinet.
• Speed range: 0 to 2000 rpm (typical), Opto-interrupter based speed sensing.
• 4-digit speed display in rpm., Electronic tachogenerator for feedback.
• Separate unit for motor with 2Kg Spring Balance provided for loading.
• Built-in 3 ½ digit DVM for signal measurements, 3 ½ digit Current Meter.

Features:

• Air Filter, Isolating Valve, Regulator & Lubricator Unit (FRL Unit)
• Pressure Manifold with Four ON / OFF Valves for multiple connections
• Single Acting Cylinder
• Double Acting Cylinder

Features:

• Hydraulic Trainer consist of flat control panel with general purpose component area and Mobile Table provided built using 40mm Aluminum profile rack.
• 04 no's of ABS plastic panel mounted on the aluminum rack with mimic diagram containing power supply with circuit breaker, Voltmeter, Ammeter Panel, Digital Temp Indicator, Digital RPM Indicator Panel, Timer Panel, Push Button, Electro Magnetic Relay Panel & 24V DC Panel